LS Security | Residential and Commercial Alarms
  • Home
  • Services
  • Products
    • Products
    • Residential Alarm Systems
    • Commercial Alarm Systems
    • Camera Surveillance Systems
    • Wireless Monitoring
    • Home Automation
    • Card Access Systems
    • Medical Panic Systems
  • Help Desk
  • Alarm.com Help
  • Clients
  • Contact Us
  • Menu Menu
  • Facebook
Communication Test

Communication Test



1. Press  until SYSTEM TESTS

2. Enter Master Code then press 

3. Press  until COMM TEST then press 

 

4. A test signal is sent to the LS Security Monitoring Station

6. Test Signal Sent OK displays if successful or Com Failure if fail

Sensor Test

Sensor Test


1. Press  until Sensor Tests then press 

2. Enter Master Code then press 

  • Door/Window Sensor – Open and close the door or window
  • Motion – Press top button then remove and replace front of motion
  • Smoke or CO Detector – Hold test button
  • IQ Flood Detector – Open cover to tamper
  • IQ Glassbreak – Pull cover from base-place
  • Round (Hockey puck) Flood/Freeze Sensor – Look for the raised line on the side of the sensor | use a strong magnet (like one from the door contacts) and tap the sensor directly on the magnet and release.  Then hold for 5 secs on the magnet and release.

4. Simon XT beeps 1 to 8 times indicating signal strength

  • 1 to 3 beeps = Poor
  • 4 to 5 beeps = Marginal
  • 6 to 8 beeps = Excellent

5. Sensor Tests exits when all sensors are tested or by pressing STATUS

Power Cycle The Panel

Power Cycle The Panel


1. Remove top screw then press two tabs to open front cover

2. Flip front cover down

3. Apply pressure to spread the battery clips and remove the battery from tray

4. Remove the red and black battery terminal wires and wait 10 secs

5. Connect red terminal to red wire and black terminal to black wire and install into battery tray (Red and black wires go below or outside of the bottom battery clip.  Do not let the wires get clamped by the white mounting clip.)

6. Flip front cover up to close and finish

AC Power Failure

AC Power Failure


If you check the status on your alarm panel and you have an “AC power failure” it means that the panel is unplugged or there is a problem with the power connections. Here are some things to check.

(If you are experiencing a power outage you must wait for it to come back on you can silence the trouble beeps by clicking here.

First make sure the power supply is plugged in. If it is, unplug it for a minute and plug a lamp or other device into the outlet to make sure that the outlet is working properly and that your circuit breaker hasn’t blown.

If you are still not getting AC power to the panel you will need to check the power wire connections, make sure the wire is securely attached to the two screws on the back of the power plug. Also check in the back of the panel that the wire is attached to screws 4 and 5 (the ones labeled 9 VAC). Don’t worry if you get the wires switched, it does not matter which one is on 4 and which one is on 5.

If all else fails the last step would be to call LS Security as you may have a problem with the power transformer and a technician should be sent to diagnose and replace if required.

Proudly Serving Regina

 
Capital Ford
Cargill
RPS
RCMP
Warner
Prairie Valley School Division
Cooperators
DQ
Edo Japan
Fat Burger
Fries Tallman
Titan Automotive Group
Houston Pizza
Lot Club
Luther College
Moose Jaw Ford
Popeyes
Powerland
Quiznos
Rainsoft
RIA
Robin’s
Saskatchewan Construction Association
Saskatchewan Roughriders
Subway
Town and Country
 

Contact Us

LS Security
2903 Dewdney Ave.
Regina, SK
S4T 0Y1

Tel: (306) 522-3667
Email: info@lssecurity.ca
© Copyright 2015 LS Security| Website by Strategy Lab
  • Home
  • Services
  • Products
  • Help Desk
  • Alarm.com Help
  • Clients
  • Contact Us
Scroll to top